Regency Energy Services, LLC. - Dedicated to exceptional service!
 
 
Services & Equipment
 
Regency Energy Services, LLC – Rig 101
Hubbard (Cameron) C500 on a 5 axle heavy duty carrier

 
MAST 108’-250,000 LBS.

OVERALL

108 FEET CLEAR WORKING HEIGHT WITH API RATED STATIC LOAD OF 250,000 LBS. WITH 6-LINES STRUNG. TELESCOPING STRUCTURAL MAST IS DESIGNED TO API 4-F SPECIFICATIONS AND Q-1.  CONSTRUCTED IN TWO SECTIONS WITH THE UPPER SECTION TELESCOPING INTO MID-SECTION FOR OVER THE ROAD POSITION. TOP SECTION OF MAST HYDRAULICALLY LATCHES TO MID-SECTION WHEN EXTENDED. LOCK CONTROL AT CONTROL AT BASE OF MAST. MANUAL SAFETY LOCK ENGAGED FROM LADDER AT LATCH LOCATION. INCLUDES LADDER FROM CARRIER TO CROWS NEST ON CROWN. MID-SECTION OF MAST HINGES TO THE BASE SECTION WHICH IS ATTACHED IN A VERTICAL POSITION TO REAR CARRIER FRAME BY TWO REAR LEGS AND (2) TWO HEAVY-DUTY ADJUSTABLE TURNBUCKLES. MAST HAS LARGE GIRTS AND BRACES THAT DO NOT EXTEND INSIDE, FOR EXTRA BLOCK CLEARANCE. MAST INCLUDES INSTALLATION, FRONT REST AND FOUR INTERNAL LOAD LINES TO RIG. TWO FROM CROWN AND TWO FROM TOP OF THELOWER SECTION, WITH TAIL CHAINS AND RATCHETING TYPE TIGHTENING TURNBUCKLES. Includes CLASS 1 DIV 1 EXPLOSION PROOF DERRICK LIGHT KIT for 24Hr Operations.
 
SPECIFICATIONS
HEIGHT
108 FEET
NUMBER OF LINES
 

4 OR 6 API CAPACITY
CAPACITY:
4-LINES
6-LINES
180,00 LBS.
250,00 LBS
LINE SIZE:
DRILL LINE
SAND LINE:
1 SWEDGED"
9/16"
RACKING BOARD HEIGHT:
55 FEET
CAPACITY: 2" TUBING
27,0000
ROD BASKET HEIGHT:
78 FEET





  
                                                              
CROWN ASSEMBLY

BENDER TYPE CROWN FOR 4 OR 6 LINE STRING-UP WITH CONVENTIONAL BLOCK TO HANG FLAT WITH MAST.
(1)ONE-30” DIAMETER FASTLINE SHEAVE, GROOVED 1”
 
 
Draworks:

DOUBLE DRUM DRAWWORKS PACKAGE. THE DRAWWORKS HAS 42” X 12” MAIN BRAKES AND 38” X 8” SANDLINE DRUM. DOUBLE DRUM DRAWWORKS WITH A 37,500 LB. MAIN DRUM SINGLE LINE PULL ON A BARE DRUM IN 1 GEAR. DRUM CLUTCHES ARE MOUNTED ON OUTSIDE OF FRAME FOR EASY ACCESS. DRUMS ARE MOUNTED ON DOUBLE ROW, SELF-ALIGNING, SPHERICAL ROLLER BEARINGS. ONE LINE POCKET PROVIDED IN MAIN DRUM, WITH A SPLIT STEEL WRAPPER WITH LEBUS COUNTER BALANCE GROOVING FOR 1” WIRE, WELDED TO MAIN DRUM BARREL.  DRIP PAN WITH DRAIN MOUNTED UNDER SANDLINE DRUM.

SPECIFICATIONS:                                                                                                                                                                      
MODEL 42X12 MAIN DRUM
MAIN BARREL DIMENSIONS
 
18" DIAMETER X 38" LONG
WIRE LINE SIZE
1" (SWEDGED)
DRUM CLUTCH
OUTBOARD FULL AIR TWO PLATE 24"
DRAWWORKS DRUM SHAFT
5-3/4" DIAMETER
SPEEDS
6 FORWARD AND 1 REVERSE
DRUM DRIVE CHAIN
ASA 140 (1-3/4") SINGLE
BRAKE RIM SIZE
42" DIAMETER X 12" WIDE
BRAKE COOLING
WATER SPRAY
BRAKE ASSIST
SINGLE DISC 4" X 10.5" X 48.5"
ASSIST COOLING
AIR 
 Sand Line:

MODEL 38X8 SAND DRUM
SANDLINE DRUM DIMENSIONS
12-3/4" DIAMETER X 40" LONG
WIRE LINE SIZE
9/16"
CAPACITY
14,600'
DRUM CLUTCH
OUTBOARD FULL AIR SINGLE PLATE 24"
DRUM SHAFT
5" DIAMETER
DRUM DRIVE CHAIN
ASA 140 (1-3/4") SINGLE
BRAKE RIM SIZE
38" DIAMETER X 8" WIDE
BRAKE COOLING
WATER SPRAY
DRAWWORKS FRAME

FRAME IS MADE FROM A MILD STEEL STRUCTURE UTILIZING STRUCTURAL MATERIAL AND ONE-PIECE 1/2” DRAWWORKS SIDE PLATE.      
                                                            
                                                        
DRUM BRAKES

HARDENED STEEL ONE-PIECE BRAKE FLANGES, HARDENED SURFACE AT 52-54 ROCKWELL AND GROUND SMOOTH. BRAKE RIMS ARE REMOVABLE WITH RINGS FOR SPLASH WATER COOLING.  BRAKE OPERATION SHAFTS ARE MOUNTED ON BALL BEARINGS AND ARE SELF-ENERGIZED TYPE FOR POSITIVE APPLICATION AND RELEASE BY OPERATOR. BRAKE BANDS WITH BLOCKS ARE API DRILLED, FULL WRAP DEAD-END EQUALIZED.
 
DRUM BRAKES COOLING WATER SPLASH

INCLUDES AIR PRESSURIZED WATER SYSTEM WITH 60 GALLON RESERVOIR, FILLER, AIR AND WATER PIPING FROM RESERVOIR TO MAIN DRUM BRAKE. WATER PIPING IS COMPLETE WITH CONTROL VALVE AT OPERATOR’S POSITION AND CUT-OFF VALVE AT RESERVOIR TO SHUT OFF ALL PRESSURE TO TANK
 
BRAKE ASSIST
ASSIST BRAKE IS PIPE RETARDATION USED IN CONJUNCTION WITH BAND TYPE BRAKES. THE DOUBLE DISC ASSIST SYSTEM INCLUDES TWO AIR/SPRING CALIPERS, TWO QUICK RELEASE RELAY VALVES, CONTROL VALVE AND TWO KOBELT 4” X 7” X 48” DISCS MOUNTED ON MAIN SHAFT OUTSIDE DRAW WORKSFRAME. ENCLOSED IN A WELL-VENTILATED COVER WITH AIR SPACE UNDER DISC TO PULL IN COOL AIR. 
 
DRAWWORKS DRIVE

CONSIST OF ASA 140 (1-3/4”) PITCH, SINGLE STRAND, and ROLLER CHAIN. CHAIN DRIVE FROM INPUT SPROCKET TO SPROCKET ON JACKSHAFT. ASA 140 (1-3/4”) PITCH, SINGLE STRAND, ROLLER CHAIN, FINAL DRIVES TO MAIN DRUM. ALL CHAINS ARE IN OIL BATH CASE OUTSIDE DRAWWORKS. OIL LEVEL CHECK IS PROVIDED BY WINDOW MOUNTED IN CHAIN CASE.
 
RIGHT ANGLE GEARBOX

CAMERON HEAVY-DUTY 2:46 TO 1 RATIO, 580 H.P., RIGHT ANGLE GEARBOX WITH OIL BATH LUBRICATION FOR GEARS AND BEARINGS. INCLUDES INSTALLATION ON CARRIER FRAME, INPUT TORQUE SHAFT FROM TRANSMISSION TO GEARBOX AND POWERSHAFT TO DRAWWORKS DRIVE SPROCKET.
 
CONTROL CONSOLE

CONTROL CONSOLE IS LOCATED AT OPERATOR’S POSITION NEAR BASE OF MAST PROVIDING GOOD VISIBILITY OVERHEAD, TRAVELING BLOCK, AND WORK AREA. MAIN DRUM CONTROL CONSISTING OF MECHANICAL BRAKE LEVER AND COMBINATION AIR CLUTCH AND ENGINE THROTTLE VALVE. HYDRAULIC
AND AIR GAUGES, ELECTRONIC TRANSMISSION SHIFT CONTROLS. STANDARD ENGINE SHUT DOWN. EMERGENCY SHUT DOWN PROVIDED (WINCH MODE ONLY). PLATFORM PROVIDED FOR OPERATOR. CONSOLE CAN BE ELEVATED TO A HEIGHT OF 30’ VIA A CABLE SYSTEM AND CATLINE WINCH. ALL NECESSARY BRAKE LINKAGES ARE PROVIDED SO THAT CONSOLE CAN BE OPPERATED AT VARIOUS HEIGHTS.
 
SANDLINE DRUM CONTROL

SANDLINE DRUM CONTROL CONSISTING OF MECHANICAL BRAKE LEVER AND COMBINATION CLUTCH AND ENGINE THROTTLE VALVE LOCATED ON PANEL ON OPERATOR’S SIDE OF DRAWWORKS FRAME.
 
LUBRICATION

CENTRALIZED LUBRICATION SYSTEM TO ALL DRUM BEARINGS AND BRAKE LINKAGE ON DRAWWORKS. ALL GREASE FITTINGS FOR DRAW WORKS LOCATED ON OUTSIDE OF FRAME FOR EASY SERVICING.
 
HANDLING WINCH

2 HYDRAULICALLY POWERED PLANETARY WINCHES 8,000 LB. PULL, RATED AT 300’ PER MINUTE AT 50 GPM AT 2,100 RPM. RATINGS ARE FOR FIRST WRAP ON DRUM. (FAIL SAFE BRAKE, WINCH PULL-IN-OUT AND RUN-OUT IS HYDRAULICALLY POWERED). WINCH SHEAVES ARE PROVIDED IN CROWN. WINCH CONTROLS ARE LOCATED AT OPERATOR’S POSITION.
 
TONG CIRCUIT

TONG HYDRAULIC CIRCUIT IS DESIGNED TO OPERATE UP 50 GPM 2,000 PSI AT 2,100 RPM, (INTERMITTENT DUTY). INCLUDES CONNECTORS, PRESSURE AND RETURN LINES, PRESSURE GAUGE, DIRECTIONAL FLOW VALVE, AND PRESSURE REGULATING VALVE.
 
AIR SPIDER CONTROL

AIR CONTROL LINES TO REAR OF UNIT, AIR VALVE AT OPERATOR’S POSITION ON CONSOLE, AND QUICK DISCONNECT FOR AIR SPIDER FOOT CONTROL.
 
 
 
 
 
ENGINE & TRANSMISSION
 
ENGINE ASSEMBLY

(1) 60 SERIES TIER III, 14.00 LITER DETROIT DIESEL 500  HP AT 2,100 RPM WITH LIMITING SPEED GOVERNOR, AIR THROTTLE, AND SAE #1 FLYWHEEL HOUSING. EXHAUST DIVERTED TO OFF-OPERATORS SIDE WITH SPARK ARRESTERS. PERMANENT TYPE ANTI-FREEZE. DRY TYPE AIR CLEANER, WITH PRE-CLEANERS. LUBE AND OIL FILTERS. 28 CFM COMPRESSOR DRIVEN FROM ENGINE. 100 AMP ALTERNATOR, 12-VOLT HIGH AMBIENT (125 F, 52 C), HEAVY DUTY RADIATOR AND FAN. SHUTDOWNS FOR LOW OIL PRESSURE, LOW COOLANT LEVEL, AND HIGH OIL TEMPERATURE. INCLUDES INSTRUMENTS FOR WATER TEMPERATURE, OIL PRESSURE.
 
ENGINE SPECIFICATION
MODEL NUMBER
SERIES 60 TIER III
VERSION
INLINE 6 CYLINDER
DISPLACEMENT
14.00 L
BORE AND STROKE
5.1" X 6.3"
RATED POWER OUTPUT
500 H.P. 


    
                                                                 
TRANSMISSION

(1)    ALLISON 5620 AUTOMATIC TRANSMISSION PROVIDES 6 FORWARD GEARS AND 1 REVERSE GEAR. INCLUDES DROP BOX WITH DISCONNECT CLUTCH FOR DRAWWORKS OR ROAD DRIVE. AIR OVER HYDRAULICS DUAL CONTROLS WITH AIR INDICATOR. POWER SHIFT FROM CAB AND REAR CONTROL. INCLUDES PRESSURE GAUGE, AND CONVERTER TEMPERATURE GAUGE, AND TRANSMISSION OIL COOLER.

BLOCKS

                175 TON MCKISSIC, 6 LINE BLOCKS.
 
                XK-100 POWER SWIVEL,
 
  • MAX TORQUE: 7,000 FT-LBS
  • MAX SPEED: 150 RPM
  • MAX STATIC LOAD RATING: 100 TONS
  • 100 RPM DYNAMIC LOAD RATING: 98 TONS
  • MAX CIRCULATING PRESSURE: 5000PSI
  • GOOSENECK CONNECTION: 2-1/2" API L.P.
  • GOOSENECK VERTICAL ACCESS PLUG: 2-1/2" API L.P.
  • FLUID PASSAGE BORE THRU STERN: 2" I.D.
  • STANDARD STEM CONNECTION: 2-7/8" I.F.
  • SAVER SUB MAKEUP TORQUE: 7,900 FT-LBS
  • WEIGHT: 1,200 LB

 
 
PUMP
JWS340 NATIONAL PUMP POWERED BY A NEW C-9 CAT WITH A MANUAL  7-SPEED TRANSMISSION MOUNTED ON AN OILFIELD SKID WITH A 3 X 4 HYDRAULIC DRIVEN CHARGE PUMP W/ HYDRAULIC DRIVEN CHARGE PUMP, 4-VALVE REVERSE MANIFOLD WITH TWO CHICKSANS, MUD PRESSURE GAUGE, SHEAR RELIEF, AIR CHAMBER, 90 GALLON FUEL TANK, 60 GALLON HYDRAULIC TANK, PIPE RACK WITH 10 JOINTS OF HARD LINE W/ 1503 UNIONS.









PIPE WRANGLER


 




















         
BASE BEAM
1 – 40’ X 4’ X 12” STYLE RIG UP BEAM:                                                                   
  • 6” SCHDULE 80 PIPE FOR TOW BARS                    
  • 3/8” DECKING ON BOTTOM                     
  • 1/4” DIAMOND PLAT DECKING ON TOP                     
  • 1” LUGS FOR GUY LINES.                  
  • INTIGRATED BASKETS AND TOOL CARRIERS
 
 
 
 
 
 
 
 
 


MUD TANK

120 BARREL, 2 COMPARTMENT MUD TANK, WITH LADDERS, RAILING, STAAIRS, HOPPER, DEGASSER, HARDLINE RACKS, & 5 JOINTS OF HARDLINE.
 
PIPE RACKS   

     
                                                    
DOG HOUSE, PARTS HOUSE, OFFICE COMBONATION TRAILER   
  











PRESSURE WASHERS/ ENVIRONMENTAL RESPONSE TRAILER


ADDITIONAL EQUIPMENT AND SERVICES

·         LOADERS
·         WINCH TRUCKS
·         HEAVY HAUL
·         SIDE DUMPS
·         TANKERS
·         CLEAN AND DRIFT CREWS
·         GENERATORS AND LIGHT TOWERS
·         ANCHOR PROTECTORS
          MUD MOTORS
          MILLS AND BITS
       


 
 
 
 
 
 
Website Builder provided by  Vistaprint